Skip to content

Home / The GTI Stake

Patent US 10,653,079

The GTI Underground Tree Stake (Patented)

Take it. Stake it. Leave it.

See it go in

1 Minute Install Video. Enjoy.

The GTI Tree Stake is a completely underground tree support system that supports the root ball allowing the tree to avoid blow over while the tree's roots naturally take hold into the newly planted area. The GTI Tree Stake is simply installed when the tree is placed in the planting hole, completely covered when the hole is backfilled with soil, and requires no wires, posts or any above ground presence whatsoever. The best part is that there is no removal as the GTI Tree Stake will simply decompose into the Earth and actually provide iron for the tree for years to come.

1 Minute Install Video

NO posts. NO wires. NO removal.

NO damage to the tree or rootball.

Take it. Stake it. Leave it.

  • No posts. No wires. No removal.
  • No damage to the tree or rootball.
  • Supports the root ball to help avoid blow over while roots take hold.
  • Decomposes over time and provides iron back into the earth.
FINISH GRADESADDLE ANDSTABILIZER3 U-STAKES#3 REBAR30 INNOTHINGABOVE GRADEPOSTSAND TIESTIE ONTHE TRUNKROOT BALLUNDISTURBED SOILBACKFILL65 GAL TREE · 30 IN ROOT BALL · LARGE UNIT · PROPORTIONS APPROXIMATE

Installation

How It Works

Simple installation in minutes, with no special tools required.

One unit per tree

One unit per tree

Each unit is 1 saddle, 1 stabilizer and 3 U-stakes, all #3 rebar.

Install the stake while the tree is being planted, before backfill. The tree should be plumb before staking.

In the ground

What it looks like before the soil goes back

Once the hole is backfilled there is nothing left to photograph. These were taken just before.

Root ball in an open planting hole with GTI U-stakes running down beside it
Open hole, before backfill. The U-stakes run down beside the root ball.
GTI saddle and stabilizer set on the root ball of a large tree
Saddle and stabilizer on the root ball of a large tree.
GTI saddle and U-stake on a root ball at a commercial site
On a commercial site in Colorado, just before backfill.

Patented

US Patent 10,653,079

Issued May 19, 2020. These are drawing sheets from the patent itself.

Patent figure 18: plan view and section view of the underground tree stake on a planted tree
Fig. 18. Plan and section, planted tree.
Patent figure 8: section through the planting hole with the stakes driven, and plan view
Fig. 8. Stakes driven, section and plan.
Patent figure 1: the saddle and stabilizer
Fig. 1. Saddle and stabilizer.

Read the full patent

Field trial

Installation Time

Timed side by side against traditional staking in a 2015 Rice University trial.

15 gal Texas Redbud

GTI Stake
1 min
1 person
2 stakes + tie
5 min
2 people

30 gal Crape Myrtle, multi-cane

GTI Stake
1 min
2 people
3 stakes + tie
6 min
2 people

Source: Rice University, 2015. Two tree types, timed installation, measuring elapsed time and crew size. Figures are from single trials and are not a controlled study of holding strength.

Sizing

One unit per tree, four sizes

ContainerRoot ballGTI stake size
10 gal16 inSmall
15 gal18 inSmall
20 gal20 inSmall
25 gal22 inMedium
35 gal24 inMedium
45 gal26 inLarge
65 gal30 inLarge
100 gal plusX-Large

From the GTI Stake detail. One unit per tree.

Sizing tool

Which unit fits the tree?

Size it the way the tree is sold.

Pick the container size in gallons.

Construction

Specifications

How the GTI Stake is built, and why it costs less to install.

ProductGTI Stake (Underground Tree Support System)
Material#3 (3/8 in) steel rebar, ASTM A615, Grade 40 or 60
One unit1 saddle, 1 stabilizer, 3 U-stakes
SizesSmall, Medium, Large, X-Large
Spec section32 9400
PatentUS 10,653,079

Product Construction

The GTI-Stake uses two pieces, aka the “saddle” and “stabilizer”, made of #3 (3/8 inch diameter) rebar that interlock to form a triangular shape that rests directly on top of the root ball. The stabilizer bar is then connected to the saddle and creates a proprietary locking and engagement system. This engagement system holds strong in any wind direction creating two engagement points at all times, holding the tree firmly in place, even in extreme high winds.

Each point of the saddle is anchored by a #3 rebar U-stake. When planting in rocky ground, holes are drilled and the same U-stakes are set into them (see the method here). The stakes are then hammered into place just below the top of the root ball.

The plant hole is back-filled with the selected fill and mulch is applied to the tree well. Over time the rebar will rust away back into the Earth so there is no need to remove the stakes and will provide the soil with iron that can be absorbed by the tree.

Cost Efficiency by Design

The reduction in cost was achieved by removing all welding and focuses the design on bending and cutting. The GTI-Stake was designed so that one system can be made from a single 20ft piece of rebar leaving zero material waste. This allowed for the design to be simpler to install than above ground tree staking systems and reducing the cost of labor to install.

When designing the GTI-Stake, GTI's driving focus was to create strong, sustainable, reliable and more cost-efficient products. This makes the GTI-Stake much less expensive than typical below ground tree stakes and even rivals most above ground system's pricing as well. By doing this, GTI removed the issue of below ground stakes not being a cost-efficient solution when planting a large number of trees and a viable option for large scope planting projects.

Why it exists

GTI develops products for the landscape and agriculture industry with the most valuable asset in mind, our Earth. The GTI-Stake was created in response to above ground staking methods which hinder the growth, health, and the aesthetic natural beauty of the tree. Development also centred on design and materials in response to alternative underground support options lacking cost efficiency, which are often cut to meet budget requirements. Our product rivals traditional staking system prices, in no way harms the trees, has zero post planting labor, and is completely biodegradable.

Specifiers

For Landscape Architects

For Landscape Architects who would like the proper specification documents for placement into your plans, the three documents below open directly. Please add info@gingertreeinnovations.com to your contact list to ensure our emails are getting to you.

Download Details

Copy the written spec text and register a project

CAD

If DWG files are needed, request them here

We email the DWG detail, usually within one business day.

Questions

Asked on most first calls

Do the stakes ever need to come out?

No. The GTI Stake is covered when the hole is backfilled and stays there. Over time the rebar rusts away back into the earth and provides the soil with iron that can be absorbed by the tree.

What comes in one unit?

1 saddle, 1 stabilizer and 3 U-stakes, all made of #3 (3/8 inch diameter) rebar. Use one unit per tree.

Which size do I need?

Small fits 10, 15 and 20 gallon containers. Medium fits 25 and 35 gallon. Large fits 45 and 65 gallon. X-Large fits 100 gallon and up. The sizing table is on the GTI Stake detail.

Can it be added after the tree is planted?

No. GTI stakes are designed to be installed during tree installation, before backfill, and will not perform to their maximum capability unless installed that way.

What about rocky ground?

Drill a hole for each stake leg, set the same U-stakes into the holes and tap them down so the top sits about 1 inch below the top of the root ball. There is no separate part for rock. The rock installation video shows the method.

Is there a written specification?

Yes. Section 32 9400, GTI Tree Stake, is a free download along with the detail sheet. DWG files are sent on request.

Where do I buy it?

In the Austin area, Leaf Landscape Supply. In the Dallas area, Horizon Distributors. In the Houston area and outside Texas, contact GTI directly.

Ready to try it on your next planting?

Find the nearest stocking location or count the units for a job.